Skip to main content
Back to Chemistry

KINETICS · THE IODINE CLOCK

Arrhenius Kinetics Lab

Intro college

INTRO COLLEGE · CHOOSE WHERE TO START

How much does 10 °C matter?

Mix iodide and peroxydisulfate in water baths from 5 °C to 45 °C and time how long the flask takes to turn blue-black. From the times you find the rate constant k, the activation energy Ea, and what a copper catalyst changes.

Each lab: Pre-lab → Bench → Data & graph → Claim · Evidence · Reasoning → Test. Goes further than AP Chemistry Unit 5 (kinetics). Your work saves on this device as you go.

About this model

The reaction. Peroxydisulfate oxidizes iodide: S₂O₈²⁻ + 2I⁻ → 2SO₄²⁻ + I₂, with rate = k[S₂O₈²⁻][I⁻]. A fixed 5.00 × 10⁻⁵ mol of thiosulfate turns the first I₂ back into I⁻; when it is used up, I₂ (as I₃⁻) meets the starch and the flask turns blue-black. So every run times the same Δ[I₂] = 5.00 × 10⁻⁴ mol/L. Because thiosulfate regenerates I⁻, [I⁻] stays constant, and [S₂O₈²⁻] falls by only 2.5 % before the blue, so the model treats each run as an initial rate.

The numbers. k follows the Arrhenius equation, k = A·e^(−Ea/RT), with R = 8.314 J mol⁻¹ K⁻¹. Without a catalyst Ea = 51.9 kJ/mol, the value a common General Chemistry handout gives as accepted (published values run from about 42 to 56 kJ/mol and depend on the ionic strength). k at 25 °C is set to 4.0 × 10⁻³ L mol⁻¹ s⁻¹ so the 25 °C clock takes about 2.6 minutes, as it does in classroom labs; that calibration is a teaching choice. With 4 drops of CuSO₄ the model uses Ea = 34 kJ/mol and a k three times larger at 25 °C. Course labs agree that Cu²⁺ lowers Ea clearly but report no single value, so these are illustrative. The catalyzed A is smaller than the uncatalyzed A because only a trace of Cu²⁺ is present (A includes [Cu²⁺]).

Your data. Each bath’s real temperature differs a little from its label (an ice bath is never exactly 5.0 °C), and every run has about 1.5 % timing scatter, as mixing and judging the first blue do in a real lab. The numbers are made up but realistic, and different for each student. The stopwatch runs as a time-lapse so a 12-minute cold run takes a few seconds; the time recorded is the real one, stopped at the first blue-black as a light sensor would.

The energy distribution is the textbook Maxwell–Boltzmann shape, drawn schematically: the energy axis is squeezed so the tail above Ea can be seen (the real Ea is about 21 RT at 25 °C, and only about 1 collision in a billion has that much energy). The numbers printed in Explore are the Arrhenius factor e^(−Ea/RT), the share of collisions with at least Ea in simple collision theory. The energy diagram is not to scale.

Limits. Real reactions in water have ionic-strength and diffusion effects, the starch–iodine colour weakens above about 50 °C, and copper(II) can also form a little CuI. The model leaves these out.

What am I looking at?

How the lab works. Pick Explore or one lab at the top. Each lab has five tabs: Pre-lab, Bench, Data & graph, Claim · Evidence · Reasoning, and Test. On the Bench, the coach always shows your next step and ticks steps off as you work.

The bench. Five water baths (1 L beakers): an ice bath at 5 °C, a cool bath at 15 °C, room temperature at 25 °C, and two baths on hot plates at 35 and 45 °C. Each has a thermometer; its reading is the temperature you record. The reaction flask (iodide, thiosulfate and starch) sits in the bath you choose. In Explore (and at the end of Lab 2) an adjustable bath can be set to any temperature.

Running the clock. Choose a bath (tap it or its button), then press Mix & start. The graduated cylinder pours in 20.0 mL of peroxydisulfate and the stopwatch starts. Nothing shows until the thiosulfate runs out; then the flask turns blue-black and the stopwatch stops. Long runs play as a time-lapse. Each run goes into your notebook.

The graphs. “My results” plots your runs. “Collision energies” shows how many particles have each energy at the chosen bath; the shaded tail is the share with at least Ea. In Lab 3 and Explore an energy diagram shows the one-hill path and the two lower hills with Cu²⁺.

Keys. 1–5 = choose a bath · M = mix & start · C = catalyst on/off (Lab 3, Explore).