Skip to main content
Back to Chemistry

MATTER · SOLUTIONS

Colligative Properties Lab

Intro college
File ▾

INTRO COLLEGE · GENERAL CHEMISTRY II

Why does salt melt ice? Freeze it and find out.

Dissolved particles lower the temperature at which water freezes. The more particles per kilogram of water, the lower it goes: ΔTf = i·Kf·m. You will measure it on a real freezing-point setup.

Goes further than AP Chemistry Unit 3. Molality, van ’t Hoff factors and finding a molar mass from a freezing point are first-year college chemistry.

  1. Weigh the solute and the water on the balance.
  2. Cool the test tube in the ice–salt bath while it is stirred, and watch the cooling curve.
  3. Read the freezing point by extrapolating the cooling curve, then record it.

Choose where to start:

About this model

The laws. ΔTf = i·Kf·m and ΔTb = i·Kb·m, with Kf = 1.86 °C·kg/mol and Kb = 0.512 °C·kg/mol for water (OpenStax Chemistry 2e, Table 11.2). Molality m = moles of solute ÷ kilograms of water, which is why the lab weighs the water.

Van ’t Hoff factors. Non-electrolytes (ethylene glycol, Compound U) use i = 1. Measured values for the salts: NaCl 1.9 (OpenStax Chemistry 2e, Table 11.3, measured at 0.050 m; ideal 2) and CaCl₂ 2.6 (freezing points measured by Gibbard and Fong, 1975, at 0.05–0.3 mol/kg, tabulated by Staples and Nuttall, J. Phys. Chem. Ref. Data 6, 385, 1977; ideal 3). Real values change with concentration (they come closer to the whole number as the solution gets more dilute). This model holds each one fixed. “Ideally” in Explore uses the whole numbers instead.

The cooling curve. The tube cools by Newton’s law toward a −15.0 °C ice–salt bath from 20.0 °C (rate constant 1/70 per second). It supercools by about 1 °C with stirring (about 2 °C without) before ice forms; then the latent heat released warms it back to the freezing point. As ice forms, the same flow of heat into the bath keeps freezing water (latent heat 334 J/g, heat capacity 4.18 J g⁻¹ °C⁻¹). Ice is pure water, so the solution left behind gets more concentrated and its freezing point falls: the plateau slopes down. The bath temperature, cooling rate and amount of supercooling are illustrative, chosen to look like a classroom run.

Reading the freezing point. A straight line is fitted to the sloping part from 10 s to 50 s after ice first forms and extended back to where it meets the cooling curve of the liquid. Read this way, ΔTf comes out within about 1 % of i·Kf·m (a few percent for very small ΔTf). The probe reads to 0.01 °C with a random error of up to ±0.01 °C; the balance reads to 0.01 g, and a weighed portion lands within ±0.04 g of the amount aimed for.

What is left out. The model is for dilute solutions in water at about 1 atm. It has no eutectic (salt water cannot get colder than about −21 °C before salt crystals also form), no heat of solution, no toxicity or corrosion, and no field performance of road salts. Real 50 : 50 antifreeze freezes near −37 °C, far outside this dilute model. Boiling points in the table are predictions from ΔTb = i·Kb·m, not measurements. The bench picture is a schematic and not to scale.

What am I looking at?

How the lab works. Pick Explore or one lab at the top. Each lab has five tabs: Pre-lab, Bench, Data & graph, Claim · Evidence · Reasoning, and Test. On the Bench, the coach shows your next step; steps tick themselves as you work. Press What do I do now? when you’re stuck.

The bench. On the left, an electronic balance that reads to 0.01 g, and the bottle of the solute you chose. On the right, a test tube held by a clamp in a beaker of crushed ice and rock salt (the ice–salt bath, about −15 °C). A wire-loop stirrer moves up and down in the tube, and a steel temperature probe sends readings to the digital thermometer. White needles in the tube are ice crystals.

One trial. Choose the solute, weigh it, weigh the water into the tube, then put the tube in the bath. The cooling curve draws itself. When the run ends, slide the cursor on the graph to where the dashed lines cross, and record the freezing point.

The cooling curve. Temperature against time. The liquid cools, dips below its freezing point (supercooling), then jumps back up when ice forms. For pure water the curve then stays flat at 0.00 °C. For a solution it slopes down, because the ice is pure water and the solution left behind gets saltier. The freezing point is where the extended sloping line meets the cooling curve of the liquid.