Skip to main content
Back to Chemistry

MEASUREMENT · DENSITY, BUOYANCY AND FLUIDS

Density & Buoyancy Lab

File ▾

CHOOSE YOUR INVESTIGATION LEVEL

Does a bigger piece have a bigger density?

Both levels use the same bench: a balance and graduated cylinder, a beaker of liquid, an oil-and-water column, a spring scale over a deep tank, a pressure probe, a hydraulic lift and a pipe.

About this model

What kind of model. Codex’s science core (model.js, density-data.js): exact, steady, ideal-fluid relationships with g = 9.8 m/s² (the same value as Float Factory) and a standard atmosphere of 101 325 Pa (the same as the Gas Laws Lab). Readings are exact model values: there is no random noise, so repeating a trial gives the same numbers and does not estimate real measurement uncertainty. The 250 mL cylinder is marked every 10 mL, so its readings are shown to the nearest 1 mL (one estimated digit past the marks), and a density from them keeps the volume’s significant figures (2 for volumes under 100 cm³).

Density values. The table is the site’s teaching table (the same one Density Dash uses): gold 19.3, lead 11.34, copper 8.96, iron 7.87, aluminum 2.70, PVC 1.38, fresh egg 1.03–1.10, polystyrene 1.05, HDPE 0.95, ice 0.917, oak 0.60–0.90 (0.75 typical) g/cm³; honey 1.42, corn syrup 1.36, brine 1.15, dish soap 1.06, salt water 1.03, cold water 1.000, water 0.998, warm water 0.983, vegetable oil 0.92, isopropyl alcohol 0.79 g/mL. Real samples vary with temperature, concentration, brand, species and recipe. A density within ±2.5% of a table value (or range) makes a material a candidate; it never proves what a sample is.

① Cylinder. Water rise = the submerged volume of a rigid sample that doesn’t dissolve or soak up water (1 mL = 1 cm³). A floater stops at its waterline (it displaces its own mass of water), so its rise is less than its volume. The sinker clip holds it under; its own 2.0 cm³ (a chosen classroom value) is found with a blank run and subtracted. Bubbles, pores, melting and soaking are not modelled.

③ Column. Only vegetable oil over one water-based liquid: oil and water don’t mix, but water, salt water and brine would, so they are never stacked. An object between the two densities rests at the interface with fraction f = (ρ_obj − ρ_oil) ÷ (ρ_bottom − ρ_oil) in the bottom liquid (small rigid object, deep layers, no surface tension).

④ Spring scale. Archimedes: F_B = ρ_liquid × V_submerged × g. The sample is rigid, sealed and held still (no drag). Support needed = W − F_B: positive means the string pulls up (the scale reads it); negative means a push down is needed, so the string goes slack and the scale reads 0, never a negative number. Released, a floater rises until F_B = W; a sinker settles (F_B still acts); a neutral object has no preferred depth. The pressure probe hangs on its own cable; depth raises pressure but not the buoyant force of a rigid sample. The tank is not to scale.

⑤ Pressure. p = p₀ + ρgh for a still liquid of constant density; gauge pressure leaves out p₀. The surface pressure is adjustable because real air pressure varies.

⑥ Lift (AP enrichment). Pascal’s principle with ideal pistons (no mass or friction, same height, incompressible oil): F₂ = F₁ × A₂/A₁, travel d₂ = d₁ × A₁/A₂, so the work in equals the work out. This lift calculation is enrichment: AP Physics 1 Unit 8 covers pressure, Archimedes, continuity and Bernoulli; it does not name hydraulic-lift calculations separately.

⑦ Pipe. Continuity A₁v₁ = A₂v₂ and Bernoulli p + ½ρv² + ρgy = constant, for steady, incompressible, non-viscous flow in a full pipe along one streamline, with no pump or friction losses. “Faster means lower pressure” is true only at the same height. If the computed outlet pressure is not positive the result is marked unsupported; a positive value still doesn’t rule out boiling (cavitation) in a real pipe.

What am I looking at?

How the lab works. Pick Explore or one lab at the top. Each lab has five tabs: Pre-lab, Bench, Data & graph, Claim · Evidence · Reasoning, and Test. On the Bench, the coach lists your steps; they tick themselves as you work. Press What do I do now? when you’re stuck.

① Cylinder. The balance (left) weighs the sample; then it is lowered on a thread into a 250 mL graduated cylinder (right). The orange dashed line marks the reading at eye level. A floating sample sticks out above the water unless you tick “Hold it under with the sinker clip”. Run “Sinker clip only (blank run)” first to find the clip’s own volume.

② Liquid. The empty beaker is weighed (tare), then the liquid is poured in. Liquid mass = beaker + liquid − empty beaker. ③ Column. Gold-coloured oil floats on a blue water-based liquid; the dashed line is where they meet. Drop an object and see where it settles.

④ Spring scale. Arrows on the sample: W (red, down) its weight, F_B (blue, up) the buoyant force, T (green, up) the string. A dashed, sagging string means it is slack; the orange rod pushes a floater down. The steel ball on the right is a pressure probe on its own cable. “Release it” lets the sample go.

⑤ Pressure. The probe’s teal arrows grow as the pressure grows; the dial and chips show gauge and absolute pressure. ⑥ Lift. Push the small piston: the hatched oil that leaves the small cylinder fills the big one. ⑦ Pipe. Dots ride along with the water; the tubes above each section rise with the pressure there.

Controls. ▶ runs the station; Step › moves one quarter and pauses; the speed menu slows it to 0.1× or 0.05×. Keys: Space play / pause · → step · R reset · Z / X zoom. Drag to move a zoomed-in scene.