Skip to main content
Back to Chemistry

REDOX · PERMANGANATE TITRATION

Redox Titration Lab

AP Chemistry

AP CHEMISTRY · CHOOSE WHERE TO START

How much iron is in the flask?

Purple permanganate turns almost colourless as it oxidizes iron(II). Add it drop by drop from a buret until the first faint pink stays: that colour tells you every Fe²⁺ has reacted. Pick one lab to turn in, or explore the bench first.

Each lab: Pre-lab → Bench → Data & graph → Claim · Evidence · Reasoning → Test. Your work saves on this device as you go.

About this model

The reaction. In acid, permanganate oxidizes iron(II): MnO₄⁻ + 8H⁺ + 5Fe²⁺ → Mn²⁺ + 5Fe³⁺ + 4H₂O. Mn goes from +7 to +2 (gains 5 e⁻); each Fe goes from +2 to +3 (loses 1 e⁻). The acid is always in excess, so the ratio stays 5 Fe²⁺ : 1 MnO₄⁻ (OpenStax Chemistry 2e §17.1, §4.5). Iron is 55.845 g/mol.

The endpoint. The model reacts every drop instantly and completely. While any Fe²⁺ is left, the flask stays colourless; the first drop past equivalence leaves a lasting faint pink. On the bench a drop shows as a purple swirl that fades on swirling, more slowly near the end. That fade time is a drawing choice that copies what you see in a real flask, not a measured rate.

Colours. The flask colour uses Beer–Lambert absorbance of permanganate (strongest in the green near 525 nm, about 2.4 × 10³ L mol⁻¹ cm⁻¹) through about 4 cm of liquid, so dilute MnO₄⁻ looks pink and concentrated MnO₄⁻ looks purple. A little phosphoric acid in the flask keeps Fe³⁺ colourless; Fe²⁺ is very pale green. Mn²⁺ at these concentrations is effectively colourless.

The buret. 50 mL, read to 0.01 mL at the top of the meniscus, because KMnO₄ is too dark to see the bottom. One drop is 0.05 mL. Initial readings are never exactly zero, as in a real lab, so always subtract: used = final − initial.

The samples. Every concentration, the tablet’s mass and its iron content are made-up teaching values, different for each student, chosen to sit in realistic ranges (a 325 mg ferrous sulfate tablet holds about 65 mg iron). Real tablets contain binders that can use up a little permanganate; this model leaves them out. KMnO₄ is usually standardized against sodium oxalate; Lab 2 uses an Fe²⁺ standard (Mohr’s salt) so the whole lab uses one reaction.

The drawing. The buret scale is correct (0 at the top, 50 mL); the flask, liquid level and props are not to scale.

What am I looking at?

How the lab works. Pick Explore or one lab at the top. Each lab has five tabs: Pre-lab, Bench, Data & graph, Claim · Evidence · Reasoning, and Test. On the Bench, the coach always shows your next step and ticks steps off as you work.

The bench. The buret on the ring stand holds purple potassium permanganate, KMnO₄ (the titrant). Its scale reads 0 at the top, so the level goes down the numbers as you add. The round magnifier shows the level close up, with lines every 0.1 mL; read the top edge of the purple liquid. Below is an Erlenmeyer flask of iron(II) solution with acid, on a white tile so a faint pink is easy to see. The amber bottle is the KMnO₄ stock.

Adding KMnO₄. The buttons beside the buret open the red stopcock for 5 mL, 1 mL, 0.1 mL or one drop (0.05 mL). The flask swirls as it goes in. While Fe²⁺ is left, each purple drop fades away; near the end the colour lingers, so go drop by drop. The first faint pink that stays is the endpoint: press Record endpoint. New trial gives a fresh flask and refills the buret.

The graph beside the bench is drawn from your recorded trials (in Explore it shows what is inside the flask, which you can’t see in a real lab).

Keys. D = one drop · A = add 1 mL · R = record endpoint · N = new trial.