Skip to main content
Back to Chemistry

ACIDS & BASES · TITRATION CURVES

Titration Curve Lab

AP Chemistry

AP CHEMISTRY · CHOOSE WHERE TO START

What does a titration curve tell you?

Add titrant from a buret one drop at a time, watch the pH probe draw the curve, and use it to find a concentration, a pKa and the right indicator. Pick one lab to turn in, or explore the bench first.

Each lab: Pre-lab → Bench → Data & graph → Claim · Evidence · Reasoning → Test. Your work saves on this device as you go.

About this model

What it calculates. For every volume of titrant, the pH comes from the full charge balance and mass balance of the solution at 25 °C (Kw = 1.0 × 10⁻¹⁴), solved numerically. It does not switch between separate formulas, so it stays correct at the start, in the buffer region, at equivalence and beyond (OpenStax Chemistry 2e §14.7).

The three systems. HCl titrated with NaOH (strong acid, strong base); acetic acid titrated with NaOH (weak acid, Ka = 1.8 × 10⁻⁵); ammonia titrated with HCl (weak base, Kb = 1.8 × 10⁻⁵). All three are monoprotic: one H⁺ per molecule and one equivalence point. Acids with two or more acidic hydrogens are not in this model.

The unknown. The unknown sample is the same for everyone: a fixed made-up solution, not a real product.

Indicators. Colour-change ranges: methyl orange 3.1–4.4 (red → yellow), bromothymol blue 6.0–7.6 (yellow → blue), phenolphthalein 8.2–10.0 (colourless → pink). The flask’s colour blends evenly across the range, and the colour name changes once a tenth of the range has been crossed. Real colour judgement varies a little from person to person. Phenolphthalein fading again above pH 12 is not modelled.

What is left out. Ideal solutions (no activity corrections), instant mixing, a perfect probe, no CO₂ absorbed from the air, and one drop is exactly 0.05 mL. The pKa table in Lab 2 uses Ka values at 25 °C from OpenStax Chemistry 2e, Appendix H.

The drawing. The bench is a schematic: the buret scale is correct (0 at the top, 50 mL, read at the bottom of the meniscus) but the flask and its liquid level are not to scale. NaOH and HCl solutions are colourless; the titrant is tinted pale blue so you can see it.

What am I looking at?

How the lab works. Pick Explore or one lab at the top. Each lab has five tabs: Pre-lab, Bench, Data & graph, Claim · Evidence · Reasoning, and Test. On the Bench, the coach on the right always shows your next step and ticks steps off as you work.

The bench. A buret on a ring stand holds the titrant, a solution whose concentration you know. Its scale starts at 0 at the top, so the reading is the volume you have added. The round loupe magnifies the meniscus. Below it, an Erlenmeyer flask holds the sample and a few drops of indicator on a magnetic stir plate (the white bar in the flask spins to mix). The white card behind the flask makes colours easy to see. The pH probe in the flask is wired to the pH meter.

Adding titrant. The buttons under the bench open the red stopcock for 5 mL, 1 mL, 0.1 mL or one drop (0.05 mL). Go fast on the flat part and by drops when the pH starts to move. New flask starts over with a fresh sample and a full buret.

The graph. The probe draws pH against titrant added. The hatched band is the pH range where the indicator changes colour. The curve reader slider moves back along the curve you have drawn and shows the pH and flask colour there. Record reading saves the reader’s point (or the current one) to your data table.

Keys. D = one drop · A = add 1 mL · R = record reading. On the curve reader, the arrow keys move one drop at a time.