Skip to main content
Back to Earth and Space

GROUNDWATER · RESOURCES & HUMAN IMPACT

Groundwater & Aquifers Lab

File ▾

CHOOSE YOUR INVESTIGATION LEVEL

Where is the water under our feet, how does it move, and what happens when we pump too much?

Both levels use the same five stations: a sediment column, a well-drilling cross-section, an aquifer water budget, a tracer map and the real San Joaquin Valley subsidence record.

About this model

What kind of model. Codex’s science core (model.js) with five simple, labelled models. None of them is a groundwater flow model of a real place, and none can say whether real water is safe to drink.

① Column: Darcy’s law. Saturated, homogeneous, steady, one-dimensional flow: Q = K·A·Δh/L, Darcy flux q = Q/A, seepage velocity v = q/nₑ (Heath 1983, USGS Water-Supply Paper 2220). Porosity ranges are from USGS WRI 92-4085, table 2 (Freeze and Cherry values): gravel 25–40%, sand 25–50%, silt 35–50%, clay 40–70%. Conductivity K is the midpoint of the ranges USGS SIR 2024-5012 estimated for one study area (Elizabeth Lake), converted from ft/day (1 ft = 0.3048 m): gravel 32–100 → 20.1 m/day, sand 16–32 → 7.32 m/day, silt 0.003–16 → 2.44 m/day, clay 0–0.0033 (an upper bound) → 0.000503 m/day. These are one study’s estimates, not universal constants; silt’s range is very wide, and gravel can be far more conductive than this site’s value: textbook ranges for clean gravel run about 10²–10⁴ ft/day (roughly 30–3,000 m/day; Heath 1983, WSP 2220). The effective porosity nₑ = 0.25 is a supplied value for every material, not measured. The column stands for an L m × 50 m² slab of aquifer; the time shown is model days (1 s = 1 day at 1×). The pore picture in the magnifier is drawn.

② Wells. Codex’s schematic section (metres below land): 0–10 unsaturated, 10–30 unconfined aquifer, 30–40 aquitard, 40–70 confined aquifer, deeper than 70 bedrock. These depths are supplied, not a real site. A well’s screen is a point at its depth; its type is the layer it is in. The water stands at the water table (10 m below land) in the unconfined aquifer and at the confined head (−5 m or +2 m) in the confined aquifer; it flows only when the confined head is above land. Pumping (confined only) uses the steady Thiem equation s = Q·ln(R/r)/(2πKb) with supplied K = 5 m/day, b = 20 m, r = 10 m, R = 1000 m: confined, fully penetrating, steady radial flow with a fixed outer head, not an unconfined or changing-in-time solution. The cone is drawn 8× deeper than the depth scale.

③ Water budget. One lumped interval for an unconfined block (A = 10 000 m², base 0 m, land 10 m, specific yield 0.2 supplied): drainable storage = A·Sy·head; recharge adds rate × A × days; pumping takes what is asked for, but never more than is there (unmet = asked − pumped); storage above the land surface overflows. Specific yield is not total porosity. Because the rates are constant, the head at day t is the same budget over t days, so the drawing moves it steadily; real recharge and pumping vary.

④ Tracer. A conservative tracer in 1D: centre = 100 m + v·t with v = K·i/nₑ; spread σ = √(2Dt) with D = 1 m²/day (supplied). No sorption, reactions, density effects or pumping capture. The width across the strip is drawn. Head contours use h = 20 − i·x (a hypothetical datum, for labels only).

⑤ Subsidence. Two rounded endpoints reported by USGS for a site near Mendota, near the area of maximum subsidence in the San Joaquin Valley: 1925 (0 m) and 1977 (about −9 m); local copy in subsidence-snapshot.json. This is not an annual record, not a valley-wide average and not a forecast; the interval average (≈ 0.17 m/yr) is only an average. Clay compaction is drawn, not computed.

Repeatable. Every number on the bench is deterministic: the same settings always give the same result. Tests use a seeded draw.

What am I looking at?

How the lab works. Pick Explore or one lab at the top. Each lab has five tabs: Pre-lab, Bench, Data & graph, Claim · Evidence · Reasoning, and Test. On the Bench, the coach lists your steps; they tick themselves as you work. Press What do I do now? when you’re stuck.

① Column. A glass tube of sediment on a bench, seen from the side. Water enters from the left standpipe (head 1) and leaves at the right (head 2); the dashed amber line is the head, falling along the column. The blue dye front moves at the seepage speed; drips fill the tank at the right (the volume collected). The round magnifier shows the pores (drawn). The graph: each material’s porosity range (bar) against its conductivity (log scale): ■ gravel, ● sand, ◆ silt, ▲ clay.

② Wells. A cross-section of the ground, 0–90 m deep, with the depth on the left. Blue-tinted layers are saturated aquifers; the solid blue line ▽ is the water table; the dashed amber line ▽ is the confined aquifer’s head. Set the screen depth (or tap the section) and press ▶ Drill. The graph shows the water level a well would have at each depth: ✗ = little or no water.

③ Water budget. A block of aquifer seen from above and in front. Rain is recharge; the pump takes water out. The blue part is saturated; ▽ is the water table. The tanks on the right count the water recharged, pumped, unmet (dashed red outline, ✗) and overflowing (≈), in m³.

④ Tracer. A map strip of the aquifer, looking down. Dashed lines are head contours (h in m); arrows show the flow, from high head to low head. The magenta cloud is the tracer: ▲ is its centre, the bracket is ± σ. MW1–MW4 are monitoring wells; their bars show how much tracer is there now.

⑤ Subsidence. The San Joaquin Valley near Mendota. The pole’s signs mark the land surface in 1925 and 1977; the bracket is the drop. The clay layers below are drawn thinner in 1977 (compaction, drawn).

Controls. ▶ runs the station; Step › moves one beat (a day, a layer, a tenth of the run, 10 days, or the other year) and pauses; the speed menu slows it to 0.1× or 0.05×. Keys: Space play / pause · → step · R reset · Z / X zoom. Drag to move a zoomed-in scene.