Skip to main content
Back to Earth and Space

EARTH MATERIALS · MAPS AND LANDFORMS

Mapping Earth’s Surface Lab

File ▾

CHOOSE YOUR INVESTIGATION LEVEL

How does a flat map show hills, valleys and where the water goes?

Both levels use the same map table: build land with a brush or load a valley, a volcano or a coastline, watch contour lines redraw, slice the land into a side view and drop rain to see where it runs.

About this model

The land. A made-up 4 km × 4 km height map: 41 × 41 grid points 100 m apart, elevations in metres. The valley, volcano and coastline are smooth invented shapes (not real places or measured elevation data). The brush raises or lowers a smooth bump (height × (1 − r²)², r = distance ÷ brush radius). Between grid points, elevations are estimated by bilinear interpolation.

Contour lines. Drawn live by marching squares: on each grid cell edge, a line’s crossing is placed by straight-line interpolation. Where a cell could be read two ways (a saddle), the cell’s average decides. Every fifth line is a thicker, labelled index contour, as on USGS topographic maps. Features smaller than the 100 m grid are not shown.

Profiles. 81 elevations sampled along the line. Run is horizontal map distance; rise is the elevation at B minus at A; endpoint gradient = rise ÷ run (it can hide ups and downs in between). The profile graph stretches the vertical axis; the stretch is printed on it.

Water. Each step a raindrop moves to whichever of its 8 neighbours has the steepest downhill drop (the D8 rule: O’Callaghan & Mark, 1984). It never moves uphill and stops in a sink or on flat ground. There is no ponding and spilling, soaking in, evaporation, erosion or amount of rain. Streams are drawn where many cells drain through a point. A path that reaches the map edge leaves the map; a watershed touching the edge may be larger in reality.

Watershed outline (AP). Your outline is compared with the model’s drainage basin at the grid points: agreement = cells in both ÷ cells in either. It is a check against this model, not a measure of a real watershed.

Latitude and longitude. The map is placed near 40° N, 105° W using a flat (tangent) approximation of a spherical Earth with radius 6,371 km. This is a teaching grid, not survey coordinates. Coastline depths below 0 m are sea floor; no ocean or tides are modelled.

What am I looking at?

How the lab works. Pick Explore or one lab at the top. Each lab has five tabs: Pre-lab, Bench, Data & graph, Claim · Evidence · Reasoning, and Test. On the Bench, the coach lists your steps; they tick themselves as you work. Press What do I do now? when you’re stuck.

① The map (left). Seen from straight above, north at the top. Colours show elevation (green low, tan and brown higher, white highest, blue below sea level) and the shading is sunlight from the north-west. Brown lines are contour lines; the thick labelled ones are index contours. Dashed lines are the latitude and longitude grid; the scale bar shows 1 km.

② The 3D view (top right). The same land as a block, with the same contour lines draped over it. Drag it to turn it.

③ The profile (bottom right). The land seen from the side along your profile line, from A to B.

Tools. Probe: tap to read elevation, latitude and longitude (it snaps onto a contour line if you tap close to one). Raise / Lower: tap or drag to build or dig. Profile: drag from A to B (or tap A, then tap B). Rain drop: tap where the rain lands; ▶ runs it and Step › moves it one grid step. Watershed (AP): tap the outlet on a stream, tap points around the land you think drains to it, then Close and compare.

Keys. Click the map first. Arrow keys move the yellow cross; Enter uses the tool there. Space runs the drop, → steps it, R resets the map, Z / X zoom. Drag a zoomed map with the Probe tool to move it.