Skip to main content
Back to Biology

ENZYMES & ENERGY · ENZYME KINETICS

Enzyme Kinetics Lab

Intro college
File ▾

INTRO COLLEGE · BIOCHEMISTRY

How fast can an enzyme go?

Run real assays: mix enzyme with substrate, put the cuvette in a spectrophotometer, and read the initial rate from the climbing absorbance. A molecular view shows what is happening in the cuvette: substrate filling active sites, inhibitors getting in the way, heat unfolding the enzyme.

  1. Pick a substrate tube (or set the inhibitor, temperature or pH).
  2. Press ▶ Start 60 s assay and read the rate.
  3. Record the run, change one thing, and repeat.

Goes further than AP Biology Unit 3 (enzymes): the Michaelis–Menten equation, Vmax and Km, competitive and noncompetitive inhibition, and the double-reciprocal plot. Algebra only.

Choose where to start:

About this model

A teaching model. Every rate comes from the Michaelis–Menten equation, v = Vmax[S] / (Km + [S]) (OpenStax Biology 2e §6.5 describes enzyme saturation; the equation is the standard steady-state result). It assumes one substrate, initial rates only (no substrate is used up during the 60 s assay), and no cooperativity. The readings have no random error.

Inhibitors. Both inhibitors are reversible with the same illustrative strength, Ki = 4 mmol/L. Competitive: apparent Km = Km × (1 + [I]/Ki), Vmax unchanged. Pure noncompetitive: apparent Vmax = Vmax ÷ (1 + [I]/Ki), Km unchanged. Pure noncompetitive inhibition is a special case of mixed inhibition; many real inhibitors change both values.

Temperature and pH. These are teaching curves for a model enzyme, not measurements of a real one. Below 37 °C the rate halves for every 10 °C of cooling (Q₁₀ = 2). Above about 50 °C a growing share of the enzyme unfolds (denatures), so the rate falls steeply. The pH effect is a bell-shaped curve centred on pH 7. Real enzymes differ: catalase, pepsin and others have their own optimums.

The spectrophotometer. The substrate is colourless; one product is yellow and absorbs violet light at 405 nm, as in classroom assays that use p-nitrophenyl phosphate. The reading rises in a straight line during an initial-rate assay. The calibration here (0.0100 absorbance units per minute for each µmol/min, plus a 0.020 blank) is an illustrative value, not a real extinction coefficient.

The molecular view. Eight enzyme molecules stand for the many millions in a real cuvette. Shapes are symbolic: the substrate’s wedge fits the active site, the competitive inhibitor has the same wedge on a striped block with no bond to break, and the noncompetitive inhibitor is a green hexagon that fits the allosteric site. The share of busy active sites follows the same equations as the rates, but which molecule binds when is random. Not to scale; real enzymes are about 5–10 nm across.

Your enzyme batch. In the guided labs the enzyme’s Vmax and Km are drawn from a fixed list (Vmax 40–80 µmol/min, Km 2–6 mmol/L) using the batch number, so a run can be repeated exactly.

What am I looking at?

How the lab works. Pick Explore or one lab at the top. Each lab has five tabs: Pre-lab, Bench, Data & graph, Claim · Evidence · Reasoning, and Test. On the Bench, the coach lists your steps; they tick themselves as you work. Press What do I do now? when you are stuck.

The bench. The spectrophotometer (top left) shines violet 405 nm light through the cuvette and plots absorbance against time on its screen. The steeper the line, the faster product forms; when the 60 s run ends it shows the initial rate v in µmol/min. Faint lines are your earlier runs. The water bath sets the temperature; the buffer bottle shows the pH; the dropper vials hold inhibitors. The rack holds substrate tubes labelled with [S] in mmol/L (0 is the blank). Tap a tube or a vial to choose it; a ✓ marks tubes already recorded.

Inside the cuvette. Blue molecules are the enzyme, each with a notched active site (yellow catalytic group at the bottom) and a hexagonal allosteric site. Orange wedges are substrate; when one sits in an active site the enzyme splits it, and a yellow product and a grey product drift away. Purple striped wedges are a competitive inhibitor in the active site. Green hexagons are a noncompetitive inhibitor on the allosteric site; an enzyme holding one turns grey and makes no product. Heat leaves unfolded grey chains. At high [S] nearly every active site is busy: that is saturation.

The graph. Your recorded runs: rate against [S] (or against temperature or pH in Lab 3). The ring marks the run you just finished.

Keys: Space start / pause · → step 15 s · R clear the run.