Skip to main content
Back to Physics

ELECTRICITY & MAGNETISM · FIELDS AND INDUCTION

Magnetism & Induction Lab

File ▾

CHOOSE YOUR INVESTIGATION LEVEL

Fields from magnets, currents from changes

Every level uses the same four stations: a compass on a field map around a magnet, a wire or a coil; a motor loop between magnetic poles; a magnet pushed through a coil wired to a meter; and a hand-cranked generator lighting a lamp.

About this model

What kind of model. Codex’s science core (model.js): ideal magnetostatics and induction with μ₀ = 4π × 10⁻⁷ T·m/A (the classroom value; since 2019 μ₀ is measured, not exact, but agrees to better than one part in a billion). No Earth field is included, and a compass needle does not disturb the field it measures.

① Field map. The bar magnet is a point dipole (moment 0.5 A·m² along ±x) seen from outside: B = (μ₀/4π)(3(m·r̂)r̂ − m)/r³. The dashed circle (5 cm) marks the region next to and inside the magnet that this far-field formula does not cover. The wire is infinitely long and thin, with B = μ₀I/(2πr) circling it (current out of the page counts as positive; right-hand rule). The solenoid is a long ideal coil, 0.50 m long, with a uniform field B = μ₀NI/L inside, multiplied by an illustrative core factor (1, 10 or 20): real iron depends on its shape, saturates and shows hysteresis, and the model refuses fields above 0.05 T. The field outside the coil is not modelled. Iron filings and the needle’s swing are drawn.

② Motor. A 0.20 m wire segment along +x carrying I in a field B along +y feels F = I L × B (along ±z). A 20-turn, 0.01 m² loop with its normal at θ from B feels a torque τ = NIAB|sin θ|. This is a snapshot of force and torque: there is no spinning motor, commutator, friction or inertia. The few-degree nudge of the loop is drawn.

③ Induction coil. The magnet’s positions stand for single-turn flux values (far 0, halfway ±0.002 Wb, inside ±0.004 Wb; positive with the N pole facing the coil). emf = −NΔΦ/Δt is the average over the move; positive means counterclockwise seen from the coil’s far end. The induced current’s field opposes the change (Lenz), so the near face becomes the same pole as an approaching magnet. The meter’s swing follows the drawn speed of the magnet.

④ Generator. An ideal coil turning at constant ω: emf = NBAω sin ωt into a pure resistor lamp; RMS = peak/√2; average power P = V²rms/R. The crank must supply at least P (the induced current makes a torque that resists the turning): no friction, coil resistance or inductance, and no free energy.

What am I looking at?

How the lab works. Pick Explore or one lab at the top. Each lab has five tabs: Pre-lab, Bench, Data & graph, Claim · Evidence · Reasoning, and Test. On the Bench, the coach lists your steps; they tick themselves as you work. Press What do I do now? when you’re stuck.

① Field map. A sheet of paper seen from above, with iron filings showing the shape of the field. The compass’s red end is its north end: it points along the field. Drag the compass (or use the x and y sliders) and press ▶ Measure. ⊙ means current coming out of the page toward you, ⊗ going into it.

② Motor. You are looking down the axle of a loop of wire between the N (red) and S (blue) poles of a big magnet; the dashed lines are the field, pointing from N to S. The two copper dots are the two sides of the loop, with the current coming out of (⊙) or going into (⊗) the page. Green arrows are the forces on them; the pink arrow is the twist (torque). The gold arrow is the loop’s normal.

③ Induction coil. A bar magnet moves into or out of a coil wired to a meter whose needle rests at the centre. The circle at the right shows the induced current’s direction as seen from that end, and the badge on the coil’s face shows which pole the coil becomes while the magnet moves.

④ Generator. Turn the crank to spin the coil between the poles. The lamp glows with the power at each moment; the green screen is an oscilloscope tracing the voltage, with the peak (gold dashes) and RMS (blue dots) levels.

Controls. ▶ runs the station; Step › moves a quarter of the way and pauses; the speed menu slows it to 0.1× or 0.05×. Keys: Space play / pause · → step · R reset · Z / X zoom. Drag to move a zoomed-in scene.