Skip to main content
Back to Physics

ELECTRICITY & MAGNETISM · CAPACITORS

RC Circuits & Capacitors Lab

AP Physics 2
File ▾

AP PHYSICS 2 · UNITS 10–11

How does a capacitor store charge, and how fast?

A capacitor is two metal plates with an insulator between them. A battery pushes + charge onto one plate and an equal − charge onto the other. Through a resistor that takes time: the capacitor’s voltage rises along a curve with time constant τ = RC.

  1. Set up the plates or the circuit with the controls under the picture.
  2. Run it: on the circuit, close the switch and watch the meters and graphs.
  3. Record a reading, then change one thing and repeat.

Choose where to start:

About this model

Parallel plates. C = κε₀A/d with ε₀ = 8.85 × 10⁻¹² F/m, Q = CV and E = V/d between the plates. The plates are ideal and flat with no edge effects (fringing), so the field is uniform and stops at the edges. Plate areas run from 0.010 to 0.100 m² (10 cm to 32 cm squares) and gaps from 0.1 to 5.0 mm, so C is tens of picofarads to tens of nanofarads, like a classroom demonstration capacitor.

Dielectrics. κ values from OpenStax College Physics 2e, Table 19.1 (20 °C): air 1.00059 (shown as 1.00), Teflon 2.1, polystyrene 2.56, nylon 3.4, paper 3.7, Bakelite 4.9. The slab fills the gap. At a fixed voltage the plates hold κ times the charge; the slab’s polarization puts a charge Q(1 − 1/κ) of the opposite sign on each face, so the net field is still V/d. Real values vary with the sample, temperature and frequency.

The picture. The gap is drawn many times larger than the plates (the factor is printed), and the plates are seen from slightly above. Each ⊕ or ⊖ stands for the printed amount of charge, with equal numbers on the two plates. Each field line starts on a + charge and ends on a − charge; lines that end on the slab’s bound charges are not drawn.

The RC circuit. Two capacitors in series (1/C = 1/C₁ + 1/C₂) or in parallel (C = C₁ + C₂), a resistor R and an ideal battery V₀ with no internal resistance; ideal wires, switch and meters (the ammeter has no resistance, the voltmeter draws no current). τ = RC. Charging: V = V₀(1 − e^(−t/τ)), I = (V₀/R)e^(−t/τ). Discharging: V = V₀e^(−t/τ), I = −(V₀/R)e^(−t/τ). After one τ a charging capacitor is at 63.2 % of V₀; a discharging one keeps 36.8 %. At 5τ the current is 0.67 % of its starting value: small, not zero. Only in the limit t → ∞ is it exactly 0.

Real capacitors. The parts are electrolytic capacitors with ±20 % tolerance in real life; here they are exactly their labelled values, with no leakage, and the resistors are exact. Discharging is only allowed once the capacitor has fully charged, so every discharge starts from V₀.

Playback. A run shows 0 to 5τ in about 6 seconds, so short time constants are slowed down and long ones sped up; the printed times are the real times in the circuit.

What am I looking at?

How the lab works. Pick Explore or one lab at the top. Each lab has five tabs: Pre-lab, Bench, Data & graph, Claim · Evidence · Reasoning, and Test. On the Bench the coach shows your next step, and steps tick themselves as you work. Press What do I do now? when you’re stuck.

The parallel plates. Two metal plates on insulating posts, wired to a DC supply (red lead to the + plate). The red ⊕ and blue ⊖ circles are the charges on the plates; the yellow arrows are electric field lines from + to −. A slab between the plates is a dielectric: the small outlined charges on its faces are its polarization charges. The plate side and the gap are drawn to two different scales; the gap is enlarged so you can see inside it.

The RC circuit. A schematic: the battery (long line = +), a two-way switch (to charge through the battery, or to discharge without it), the resistor (zigzag), the ammeter Ⓐ in series, two capacitors (the + plate is straight, the − plate curved) and the voltmeter Ⓥ across the capacitors. Moving yellow dots and arrows show the direction of conventional current; they slow down as the current falls and stop when it is zero. The + and − marks on each capacitor grow as it charges.

Controls. Plates: drag the area and gap sliders (or use − and +, or the arrow keys) and tap a material. Circuit: tap a resistor or capacitor to swap it in, then use the switch buttons. After a run, drag the time cursor to read the graph at any time, and press Record reading.

The graphs. Capacitor voltage and current against the time since the switch moved. Filled circles are readings you recorded; the hollow diamond is the time cursor. The dashed line marks τ, and the dotted line is 63 % (charging) or 37 % (discharging) of the battery voltage.