Skip to main content
Back to Physics

MOTION & FORCES · FLUIDS IN MOTION

Pipe Flow & Bernoulli Lab

AP Physics 1
File ▾

AP PHYSICS 1 · UNIT 8 · FLUIDS

Where does water speed up, and what happens to its pressure?

Water flows through a clear pipe. Make one part narrower or higher and watch three things: how fast the water moves, what the pressure gauges read, and how high the water stands in the glass tubes. Then drain a tank and predict where its jet lands.

  1. Change one thing on the bench: the pipe’s size, its height, or the water in the tank.
  2. Watch the speed, the gauges in kPa and the water columns, and press Record reading.
  3. Explain your data with A₁v₁ = A₂v₂ and Bernoulli’s equation, P + ½ρv² + ρgh = constant.

Choose where to start:

About this model

It is an ideal fluid model. The water is steady (nothing changes with time at a given place), incompressible (its density stays 1000 kg/m³) and has no viscosity (no friction with the walls or within itself). Real water in a real pipe loses some energy to friction, so real pressures fall a little more along the pipe than the model says.

Continuity. Q = A₁v₁ = A₂v₂: the same volume passes every section each second. Speeds are averages over the cross-section; in this model every streamline in a section moves at the same speed, so the slices of water stay flat.

Bernoulli. P₁ + ½ρv₁² + ρgh₁ = P₂ + ½ρv₂² + ρgh₂, with ρ = 1000 kg/m³ and g = 9.8 m/s² (the AP Physics 1 value). The gauges read absolute pressure. Each piezometer column is the gauge pressure as a height of water, h = (P − 101.3 kPa) ÷ (ρg), measured from that section’s centre line. The dashed energy line is P/(ρg) + v²/(2g) + height, which stays flat in the ideal model. If the model predicts a pressure below about 2.3 kPa (water’s vapour pressure at 20 °C), real water would boil into bubbles (cavitation): the bench shows a warning and the prediction no longer applies. Below 101.3 kPa an open tube would pull air in, so its column is shown empty.

The tank. v = √(2gH) (Torricelli) for a small hole in a large open tank, a jet that leaves horizontally, and no air resistance: R = v·√(2y/g) = 2√(Hy). The tank is 50 cm across (0.20 m²) and the hole 5 cm across (20 cm²); those sizes are illustrative and only set how fast it drains: A·dH/dt = −a√(2gH). Real jets land a little short: friction at the hole and air drag slow them, and a sharp-edged hole narrows the jet just outside it.

The pictures. Heights in the pipe scene are to scale on the metre board; pipe widths are exaggerated so you can see them, but the width ratio is the true diameter ratio (diameter ∝ √area). The tank scene uses one scale for height and distance, so the jet is a true parabola. The flow animation is slowed for viewing; the ratio of speeds between the sections is exact.

Related pages. Pressure with depth, Pascal’s principle and buoyancy are in the Density & Buoyancy Lab (its Lab 3 introduces continuity and Bernoulli in one pipe). Practise hydraulics and Bernoulli energy ledgers in Hydraulic Harbor.

What am I looking at?

How the lab works. Pick Explore or one lab at the top. Each lab has five tabs: Pre-lab, Bench, Data & graph, Claim · Evidence · Reasoning, and Test. On the Bench, the coach shows your next step; steps tick themselves as you work. Press What do I do now? when you’re stuck.

The pipe. Water flows from left to right through a clear pipe. Section 1 is on the left, section 2 on the right; the controls under the picture change the section above them. The water is cut into light and dark slices that each hold the same volume, so where the pipe is narrow the slices are longer and the white tracer dots move faster.

The glass tubes and gauges. Each section has an open glass tube (a piezometer). The water in it rises until its weight balances the pressure in the pipe: a taller column means a higher pressure. Read the heights on the metre board at the left. The round gauge under each section reads the absolute pressure in kPa (the blue mark is air pressure, 101.3 kPa). The dashed gold line is the energy line: the gap between it and a column top is the speed’s share, v²/2g.

The tank. Water leaves a hole near the bottom of the tank and falls to the floor. The yellow tape on the floor starts under the hole; the yellow marker shows where the jet lands. Press Open outlet to let the tank drain and watch the level fall.

Controls. Drag the sliders (or use the arrow keys). Record reading adds what the bench shows to your data table. Keyboard on the bench: Space plays or pauses the flow (or the draining), → steps, R resets. The graph beside the bench updates as you go; filled markers are your readings and the hollow diamond is the bench now.